Download Latest Cisco 642-883 Dumps Exam Questions And Answers Free Try

QUESTION 1
You are implementing OSPF as the IGP using a single OSPF area design. The router memory usage for OSPF is too high. Which two methods can lower the Cisco 642-883 dumps OSPF memory usage? (Choose two.)
A. Enable OSPF synchronization
B. Implement multi-area OSPF
C. Enable OSPF sham links to reduce the number of LSAs
D. Implement route summarization on the ABRs
E. Enable route leaking between Level 1 and Level 2 areas
Correct Answer: BD

QUESTION 2
In which network environment is IS-IS adjacency check important?
A. in a multitopology environment where there are different instances of IS-IS running on the same router
B. in an IPv4/IPv6 environment and running single-topology IS-IS
C. when a level L1/L2 IS-IS router is neighboring with a Level 1 only or Level 2 only router
D. when IS-IS neighbors are in an NBMA environment like over Frame Relay
E. when IS-IS neighbors are in a broadcast environment like an Ethernet LAN
Correct Answer: B
642-883
QUESTION 3
Refer to the 642-883 pdf OSPF command exhibit.

Which effect does the no-summary command option have?
A. It will cause area 1 to be able to receive non-summarized inter-area routes.
B. It will cause area 1 to not receive any inter-area routes and will use a default route to reach networks in other areas.
C. It will cause area 1 to not receive any external routes and will use a default route to reach the external networks.
D. It will convert the NSSA area into a NSSA totally stubby area.
E. It will convert the stubby area into a NSSA.
F. It will disable OSPF auto-summary.
Correct Answer: B

Explanation:
642-883

QUESTION 4
When troubleshooting OSPF neighbor 642-883 exam errors, which three verification steps should be considered? (Choose three.)
A. Verify if neighboring OSPF interfaces are configured in the same area.
B. Verify if neighboring OSPF interfaces are configured with the same OSPF process ID.
C. Verify if neighboring OSPF interfaces are configured with the same OSPF priority.
D. Verify if neighboring OSPF interfaces are configured with the same hello and dead intervals.
E. Verify if neighboring OSPF interfaces are configured with the same area type.
Correct Answer: ADE

QUESTION 5
In comparing IS-IS with OSPF, a Level-1-2 IS-IS router is similar to which kind of OSPF router?
A. ASBR on a normal OSPF area
B. ASBR on NSSA
C. ABR on totally stubby OSPF area
D. ABR on stubby OSPF area
E. ABR on a normal OSPF area
Correct Answer: C

QUESTION 6
Which four statements are correct regarding IS-IS operations? (Choose four.)
A. By default, Level 1 routers within an IS-IS area do not carry any routing information external to the area to which they belong. They use a default route to exit the area.
B. Summarization should be configured on the Level 2 routers, which injects the Level 2 routes into Level 1.
C. IS-IS supports “route leaking” in which selected Level 2 routes can be advertised by a Level 1/Level 2 router into Level 1.
D. The IS-IS backbone is a contiguous collection of Level 1 capable routers, each of which can be in a different area.
E. With IS-IS, an individual router is in only one area, and the border between areas is on the link that connects two routers that are in different areas.
F. Cisco IOS XR Software supports multitopology for IPv6 IS-IS unless single topology is explicitly configured in IPv6 address-family configuration mode.
Correct Answer: ACEF

QUESTION 7
When configuring IPv4 and IPv6 IS-IS routing on Cisco 642-883 vce IOS XR routers, which three statements are correct? (Choose three.)
A. By default, a single SPF is used for both IPv4 and IPv6, so the IPv4 and IPv6 topology should be the same.
B. By default, the IS-IS router type is Level 1 and Level 2.
C. All IS-IS routers within the same IS-IS area must be configured with the same IS-IS routing process instance ID.
D. By default, metric-style narrow is used.
E. By default, the IS-IS interface circuit type is Level 1 and Level 2.
F. The area IS-IS address-family configuration command is used to specify the IS-IS area address.
Correct Answer: BDE

QUESTION 8
On Cisco 642-883 dumps IOS XR Software, which set of commands is used to enable the gi0/0/0/1 interface for OSPF in area 0?
A. interface gi0/0/0/0ip address 10.1.1.1 255.255.255.0!router ospf 1network 10.1.1.1 0.0.0.0 area 0
B. interface gi0/0/0/0ip address 10.1.1.1 255.255.255.0!router ospf 1network 10.1.1.1 255.255.255.255 area 0
C. router ospf 1area 0interface GigabitEthernet0/0/0/1
D. interface gi0/0/0/0ip address 10.1.1.1 255.255.255.0ip ospf 1 area 0
E. router ospf 1address-family ipv4 unicastinterface GigabitEthernet0/0/0/1 area 0
F. router ospf 1address-family ipv4 unicastinterface GigabitEthernet0/0/0/1area 0
Correct Answer: C

Read more: Cisco 642-883 dumps exam Service Provider is the industry leader in information technology, and getting certified by them is a guaranteed way to succeed with IT careers. We help you do exactly that with our high quality Cisco 642-883 dumps exam Service Provider Deploying Cisco Service Provider Network Routing (SPROUTE) training materials.

Reference: http://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/sproute.html