Practice exam questions and answers for Cisco 300-135, high quality Cisco 300-135 exam training materials and study guide online free update. The latest Cisco 300-135 exam test questions, 100% pass guarantee.
QUESTION 1
When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful. What is the next thing that should be checked?
A. Verify that the EIGRP hello and hold timers match exactly.
B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.
Correct Answer: D
QUESTION 2
You have been brought in to troubleshoot an EIGRP network. A network engineer has made configuration changes to the network rendering some locations unreachable. You are to locate the problem and suggest solution to resolve the issue.
R5 has become partially isolated from the remainder of the 300-135 network. R5 can reach devices on directly connected networks but nothing else. What is causing the problem?
A. An outbound distribute list in R3
B. Inbound distribute lists in R5
C. An outbound distribute list in R6
D. Incorrect EIGRP routing process ID in R5
Correct Answer: B
QUESTION 3
– (Topic 18)
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client
1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the networkaddressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolate the cause of this fault and answer the following question.
The fault condition is related to which technology?
A. NTP
B. IP DHCP Server
C. Ipv4 OSPF Routing
D. Ipv4 EIGRP Routing.
E. Ipv4 Route Redistribution.
F. Ipv6 RIP Routing
G. Ipv6 OSPF Routing
H. Ipv4 and Ipv6 Interoperability
I. Ipv4 layer 3 security.
Correct Answer: B
QUESTION 4
You have 2 NTP servers in your network – 10.1.1.1 and 10.1.1.2. You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to 10.1.1.1. Which commands will you use to configure the router?
A. ntp server 10.1.1.1
ntp server 10.1.1.2
B. ntp server 10.1.1.1
ntp server 10.1.1.2 primary
C. ntp server 10.1.1.1
ntp server 10.1.1.2 prefer
D. ntp server 10.1.1.1 fallback
ntp server 10.1.1.2
Correct Answer: C
QUESTION 5
What level of logging is enabled on a Router where the following logs are seen?
%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up
A. alerts
B. critical
C. errors
D. notifications
Correct Answer: D
QUESTION 6
Refer to the shown below.
%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up
What statement is correct regarding the output shown in the graphic?
A. These two log messages will not have a severity level. They are not errors but are just informational messages.
B. The first log message is categorized as a warning message.
C. These messages regarding interface status are normal output and will always be displayed when you exit config mode.
D. The first log message is an error message with a severity level of 3.
E. The second message would be shown if the logging console warning command had been issued.
Correct Answer: D
QUESTION 7
Refer to the exhibit. 300-135
How would you confirm on R1 that load balancing is actually occurring on the default- network (0.0.0.0)?
A. Use ping and the show ip route command to confirm the timers for each default network resets to 0.
B. Load balancing does not occur over default networks; the second route will only be used for failover.
C. Use an extended ping along with repeated show ip route commands to confirm the gateway of last resort address toggles back and forth.
D. Use the traceroute command to an address that is not explicitly in the routing table.
Correct Answer: D
QUESTION 8
In computer networking a multicast address is an identifier for a group of hosts that have joined a multicast group. Multicast addressing can be used in the Link Layer (OSI Layer 2), such as Ethernet Multicast, as well as at the Internet Layer (OSI Layer 3) as IPv4 or IPv6 Multicast. Which two descriptions are correct regarding multicast addressing? ( choose two )
A. The first 23 bits of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
B. The last 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
C. To calculate the Layer 2 multicast address, the host maps the last 23 bits of the IP address into the last 24 bits of the MAC address. The high-order bit is set to 0.
D. The first 3 bytes (24 bits) of the multicast MAC address are 0x01-00-5E. This is a reserved value that indicates a multicast application.
Correct Answer: CD
Comprehensive knowledge of Cisco 300-135 CCNP Routing and Switching products is considered a very important qualification, and the professionals certified by them are highly valued in all organizations.